2 příspěvky / 0 new
Poslední
Neznámý
Obrázek uživatele Neznámý
Jak zprovoznit - sensors

Mám prosbu, pořídil jsem si nový HW a nejsem schopen zjistit otáčky ventilátorů a teploty. V BIOSu je vše OK.
HW:
ASROCK 880G EXTREME3, AMD64 3,2 GHz Phenom II X4, RAM 4GB DDR3, disk 1000GB a 320GB
VGA Integr. ATI Radeon HD 4250, Audio ATI Radeon HD 4200, Chipset AMD SB850, DVB-T AirStar2 PCI karta - TechniSat
SW:
openSUSE 11.4, KDE 4.6.2
----------
Pomocí - "sensors" zjistím pouze:
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +23.5°C (high = +70.0°C)
(I ty hodnoty jsou zkreslené, v BIOSu cca 40-50°C. Widget mi tuto teplotu CPU ukazuje taktéž.)

Pomocí "sensors-detect" zjistím toto:
# sensors-detect revision 5861 (2010-09-21 17:21:05 +0200)
# System: To Be Filled By O.E.M. To Be Filled By O.E.M.
# Board: ASRock 880G Extreme3

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... Success!
(driver `k10temp')
AMD Family 11h thermal sensors... No
Intel digital thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... Yes
Found `Nuvoton W83677HG-I (NCT6771F/NCT6772F/NCT6775F) Super IO Sensors'Success!
(address 0x290, driver `to-be-written')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): y
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): n

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Using driver `i2c-piix4' for device 0000:00:14.0: ATI Technologies Inc SB600/SB700/SB800 SMBus
Module i2c-dev loaded successfully.

Next adapter: B2C2 FlexCop I2C to demod (i2c-0)
Do you want to scan it? (YES/no/selectively): y
Adapter cannot be probed, skipping.
Next adapter: B2C2 FlexCop I2C to eeprom (i2c-1)
Do you want to scan it? (YES/no/selectively): y
Adapter cannot be probed, skipping.
Next adapter: B2C2 FlexCop I2C to tuner (i2c-2)
Do you want to scan it? (YES/no/selectively): y
Adapter cannot be probed, skipping.
Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `to-be-written':
* ISA bus, address 0x290
Chip `Nuvoton W83677HG-I (NCT6771F/NCT6772F/NCT6775F) Super IO Sensors' (confidence: 9)

Driver `k10temp' (autoloaded):
* Chip `AMD Family 10h thermal sensors' (confidence: 9)

Note: there is no driver for Nuvoton W83677HG-I (NCT6771F/NCT6772F/NCT6775F) Super IO Sensors yet.
Check http://www.lm-sensors.org/wiki/Devices for updates.

No modules to load, skipping modules configuration.

Unloading i2c-dev... OK
Unloading cpuid... OK
--------------------
Když jdu na stránku http://www.lm-sensors.org/wiki/Devices a najdu pro "Chip" Nuvoton W83677HG-I (NCT6771F/NCT6772F/NCT6775F) odkaz z kolonky "Supported since kernel" - "standalone driver" na adrese - http://roeck-us.net/linux/drivers/w83627ehf/
soubory a nevým co s tím dál.
Poradí mi někdo?
Díky. Pepa

RNA
Obrázek uživatele RNA
Offline
Naposledy viděn: 11 měsíců 2 dny zpět
Připojen: 22.03.2010 - 21:11
Re: Jak zprovoznit - sensors

Už by to mělo fungovat.
Viz poslední můj příspěvek na http://forum.opensuse.cz/viewtopic.php?f=4&t=1690&p=5770#p5770