Mam TV kartu Twinhan DTV, bohuzel envim jak ji rozchodit v Suse 10.1. Instalator ji spravne detekuje, rozpozna, ale nic vic. Dokonce jsem v /dev nenasel zadne zarizeni, ktere by popisovalo tuhle tv kartu. Da se nejak vytvorit? Pripadne jak? Jak bych mel asi postupovat pri zprovoznovani teto karty?
Diky
Co o kartě říká příkaz hwinfo? Hodila by se informace, jaký čip je v ní použitý.
hwinfo o tomhle vypise nasledujici:
co jsem pochopil z webu, melo by to pry fungovat s bt878, bohuzel jsem ale zacatecnik a zatim mi nedochazi hodne souvislosti jak co nastavit a podobne
30: PCI 207.0: 11200 TV Card
[Created at pci.300]
UDI: /org/freedesktop/Hal/devices/pci_109e_36e
Unique ID: jqQS.2xGeltw3Zm3
Parent ID: RE4e.f9Q95vpHUcA
SysFS ID: /devices/pci0000:00/0000:00:08.0/0000:02:07.0
SysFS BusID: 0000:02:07.0
Hardware Class: tv card
Model: "Twinhan VisionPlus DVB card"
Vendor: pci 0x109e "Brooktree Corporation"
Device: pci 0x036e "Bt878"
SubVendor: pci 0x1822 "Twinhan Technology Co. Ltd"
SubDevice: pci 0x0001 "VisionPlus DVB card"
Revision: 0x11
Driver: "bttv"
Memory Range: 0xe7000000-0xe7000fff (rw,prefetchable)
IRQ: 177 (no events)
Module Alias: "pci:v0000109Ed0000036Esv00001822sd00000001bc04sc00i00"
Driver Info #0:
Driver Status: bttv is active
Driver Activation Cmd: "modprobe bttv"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #25 (PCI bridge)
31: PCI 207.1: 11100 Multimedia controller
[Created at pci.300]
UDI: /org/freedesktop/Hal/devices/pci_109e_878
Unique ID: b9wH.2Eaz8zE_JwC
Parent ID: RE4e.f9Q95vpHUcA
SysFS ID: /devices/pci0000:00/0000:00:08.0/0000:02:07.1
SysFS BusID: 0000:02:07.1
Hardware Class: dvb card
Model: "Twinhan VisionPlus DVB-T"
Vendor: pci 0x109e "Brooktree Corporation"
Device: pci 0x0878 "Bt878 Audio Capture"
SubVendor: pci 0x1822 "Twinhan Technology Co. Ltd"
SubDevice: pci 0x0001 "Twinhan VisionPlus DVB-T"
Revision: 0x11
Memory Range: 0xe7001000-0xe7001fff (rw,prefetchable)
IRQ: 177 (no events)
Module Alias: "pci:v0000109Ed00000878sv00001822sd00000001bc04sc80i00"
Driver Info #0:
Driver Status: bt878 is not active
Driver Activation Cmd: "modprobe bt878"
Driver Info #1:
Driver Status: btaudio is not active
Driver Activation Cmd: "modprobe btaudio"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #25 (PCI bridge)